Forum Replies Created

Viewing 35 posts - 106 through 140 (of 448 total)
  • Author
    Posts
  • in reply to: Help pairing bluetooth keyboard #110647
    gizmo98
    Participant

    I fear bluetooth pairing does not work if ps3 driver is installed. Disable sixad with “sudo service sixad stop” and try to pair again.

    in reply to: Gasia Co.,Ltd PS(R) Gamepad #110620
    gizmo98
    Participant

    @mrco123
    Could you test something for me? Remove your rc.local changes. Update RetroPie-Setup and reinstall PS3 controller driver with “clone support”.

    in reply to: PS3 controller pairing issue #110411
    gizmo98
    Participant

    Yes, exactly. PS3 driver is not installed by default. Once you have installed the driver it is no longer necessary to go into the RetroPie setup menu. If a ps3 controller usb “connect” is detected at runtime sixpair will be executed.

    I have modified the setup script today a little bit. So if your controller is usb connected at driver installation time sixpair will run and configure your connected controller (like in retropie < 3.1).

    in reply to: PS3 controller pairing issue #110386
    gizmo98
    Participant

    @redfarmer
    If you connect at runtime sixpair runs without user interaction. Sixpair configures your controller. This takes one second. After this second your controller should be ready for pairing. Remove USB cable and press PS button.

    As i said if your controller is configured it is not necessary to connect over usb and run sixpair again. Configuration persists.

    in reply to: No Keyboard after configuring PS3 Controller #110369
    gizmo98
    Participant

    If your keyboard connection breaks up if you type “sudo service bluetooth stop” ps3 driver is the problem.

    in reply to: PS3 controller pairing issue #110359
    gizmo98
    Participant

    @all of you
    Was the controller connected at boot up? sixpair runs if you connect your controller “at runtime” (in emulationstaion for example) and the controller should be instantly ready afterwards. If your controller is connected at boot time sixpair does not run.

    Sixpair is necessary to write the mac address of your bt dongle to the controller once. The controller should always pair afterwards.

    in reply to: Gasia Co.,Ltd PS(R) Gamepad #110323
    gizmo98
    Participant

    Remove configs/driver (no.2) before you install.

    in reply to: Gasia Co.,Ltd PS(R) Gamepad #110268
    gizmo98
    Participant

    Good to here it is running! Gasia hack + led support is broken at the moment and i don’t know if it can be fixed.

    in reply to: Bluetooth Status failed after PS3 setup #110229
    gizmo98
    Participant

    Sixad daemon stops bluetooth daemon. It’s supposed to happen.

    in reply to: Gasia Co.,Ltd PS(R) Gamepad #110198
    gizmo98
    Participant

    @slayer
    My fault. You need to checkout another branch. Please try…

    mkdir test
    cd test
    git clone --depth=1 https://github.com/gizmo98/RetroPie-Setup.git
    cd RetroPie-Setup
    git pull
    git checkout ps3-gasia-hack
    sudo ./retropie_setup.sh
    in reply to: N64 Mario Kart #109900
    gizmo98
    Participant

    I don’t know if mupen64plus “standalone” supports zip files. Please unzip file and report again.

    in reply to: Gasia Co.,Ltd PS(R) Gamepad #109883
    gizmo98
    Participant

    You can try this ps3controller module:
    https://github.com/gizmo98/RetroPie-Setup/blob/ps3-gasia-hack/scriptmodules/supplementary/ps3controller.sh

    Or type…

    mkdir test
    cd test
    git clone --depth=1 https://github.com/gizmo98/RetroPie-Setup.git
    cd RetroPie-Setup
    sudo ./retropie_setup.sh

    …and (re)install ps3controller

    in reply to: crt-pi a Pi2 friendly CRT shader #109870
    gizmo98
    Participant

    Thank you davej!
    I have added your zip file to our shader repo. If retroarch is installed/updated from source all new shaders will be fetched. So everyone can test these shaders easily.
    https://github.com/gizmo98/common-shaders/commit/7097eb6b093dc0c7722a988553d741f30b45d4fc

    in reply to: No Keyboard after configuring PS3 Controller #109869
    gizmo98
    Participant

    If your iPazzPort Keyboard is connected over bluetooth the ps3controller driver “sixad” certainly interrupts this connection. sixad disables bluetooth daemon. If you need ps3controllers and other bluetooth devices at the same time sixad must be replaced with a newer bluetooth daemon which has sixaxis support (there is no install script up to now).

    in reply to: PS3 controller pairing issue #109838
    gizmo98
    Participant

    @miahotrod
    No problem there. sixad daemon disables bluetooth daemon. Take a look into the sixad daemon script (bt_start_and_stop). I suppose bluetoothd and sixad cannot run at the same time.


    @redfarmer

    What happens if you uninstall joy2key?

    in reply to: Best possible input lag with retroarch? #109833
    gizmo98
    Participant

    Have you already disabled threaded video?

    in reply to: No Keyboard after configuring PS3 Controller #109769
    gizmo98
    Participant

    Did you setup keyboard as input device? Otherwise only button F4 is working.

    in reply to: GameBoy Shaders? #109766
    gizmo98
    Participant

    @LodanZark
    Update retroarch. There is a gameboy shader in the main shader directory now.

    in reply to: Gasia Co.,Ltd PS(R) Gamepad #109666
    gizmo98
    Participant

    I will post something if it is running.

    in reply to: Gasia Co.,Ltd PS(R) Gamepad #109530
    gizmo98
    Participant

    Just out of interest. Where can i buy this ps3 controller clone?

    in reply to: Gasia Co.,Ltd PS(R) Gamepad #109528
    gizmo98
    Participant

    There is an qtsixad package with gasia support on github. Default qtsixad does not seem to work with gasia clones.
    https://github.com/falkTX/qtsixa

    in reply to: Twin / multiple ps3 via bluetooth #109416
    gizmo98
    Participant

    Pairing a second controller should be easy. Start your pi. Wait until emulationstation appears. Connect second controller over usb. Wait some seconds. The controller should be configured now. Disconnect and press PS button.

    If this does not work please do the following steps. There was a small modification short after 3.2 release. Please press “F4” and type:

    cd RetroPie-Setup
    git pull
    sudo ./retropie_setup.sh

    Remove and install driver again.

    in reply to: Twin / multiple ps3 via bluetooth #109391
    gizmo98
    Participant

    Update retropie-setup and reinstall ps3 driver. There is a multiple ps3 controller fix now.

    in reply to: N64 "issue" not loading #109189
    gizmo98
    Participant

    I would update retropie. RetroPie 3.2.1 has more mupen64plus options and a better video plugin.

    in reply to: Mupen64Plus Issues #109150
    gizmo98
    Participant

    @lucklocky
    mupen64plus was broken in retropie sd card image 3.1. Reinstall (binary or source).

    @saucy
    I think you do not pass all necessary parameters.
    Example:
    mupen64plus –noosd –fullscreen –gfx mupen64plus-video-n64.so –configdir /opt/retropie/configs/n64 –datadir /opt/retropie/configs/n64 %ROM%”

    Please take a look here:
    https://github.com/RetroPie/RetroPie-Setup/blob/master/scriptmodules/emulators/mupen64plus.sh#L170

    in reply to: Mupen64Plus Issues #109102
    gizmo98
    Participant

    Try to install from source again. It should not segfault.

    in reply to: D-Pad does not work in game #108735
    gizmo98
    Participant

    Open /opt/retropie/configs/all/retroarch.cfg and remove
    input_player1_analog_dpad_mode = 1
    input_player2_analog_dpad_mode = 1
    input_player3_analog_dpad_mode = 1
    input_player4_analog_dpad_mode = 1
    input_player5_analog_dpad_mode = 1
    input_player6_analog_dpad_mode = 1
    input_player7_analog_dpad_mode = 1
    input_player8_analog_dpad_mode = 1

    in reply to: PS3 CONTROLLER Retropie 3.2 #108704
    gizmo98
    Participant

    Why are you using sixad-bin and stop start sixad? If you have installed ps3 controller driver over RetroPie-Setup just connect your controller over usb, wait some seconds, disconnect and press PS button. Controller should connect over bluetooth now.

    in reply to: Retroarch Menu frozen after updating to 3.2.1 #108696
    gizmo98
    Participant

    Button X opens search box. Button A or B closes search box. Our old ‘kill search box’ fix does not work anymore. But it should be possible to close this annoying field with controller now.

    in reply to: Gasia Co.,Ltd PS(R) Gamepad #108544
    gizmo98
    Participant

    Looks like a PS3 controller clone!? Try to install ps3controller module. And if it is working please post your controller config files (/opt/retropie/configs/all/retroarch-joypads).

    in reply to: N64 Emulator Exit Command #108471
    gizmo98
    Participant

    The non retroarch version supports two buttons for exit now. Syntax is “J#B#/B#”.

    If you are brave enough you can try this:
    https://github.com/RetroPie/RetroPie-Setup/issues/1061

    in reply to: Famicom Disk System – How to save your game? #108405
    gizmo98
    Participant

    If ingame save and load does not work use “select+R” to save a state and “select+L” to load a state.

    in reply to: GlideN64 Plugin #108356
    gizmo98
    Participant

    What’s happening here? Just wanted to tell you were it comes from ?. Didn’t know you already know the difference. In my opinion glide and gliden64 naming can be confusing.

    And thank you for your feedback! ?

    in reply to: GlideN64 Plugin #108280
    gizmo98
    Participant

    It’s called GLideN64. It’s from the programmer of the original Glide plugin but it’s based on the glN64 (glesn64) plugin. ;-)

    in reply to: Use 8Bitdo NES30 GamePad mopen64plus? #108269
    gizmo98
    Participant

    Do you have a 8bitdo NES30 or NES30PRO controller?

Viewing 35 posts - 106 through 140 (of 448 total)