# cp /home/pi/RetroPie-Setup/supplementary/settings.xml /home/pi/supplementary/supplementary/ES-config/

I’m not sure what is meant by that… where is the file located that needs to be edited?

I did some research: There seems to be a typo in two files
(im not sure if that is the thing gizmo98 pointed out)
First is located at:
/home/pi/RetroPie/supplementary/ES-config/settings.xml

<changeConfigPath from="retroarch.cfg" to="/home/pi/RetroPie/configs/all/retroarch.cfg" />
<changeConfigPath from="dgen.cfg" to="/home/pi/RetroPie/configs/dgen/dgenrc" />
<changeConfigPath from="gngeo.rc" to="/homepi/.gngeo/gngeorc" />

as you can see there is a / missing between home and pi

The same typo is is found in
/home/pi/RetroPie-Setup/supplementary/settings.xml

<changeConfigPath from="retroarch.cfg" to="/home/pi/RetroPie/configs/all/retroarch.cfg" />
<changeConfigPath from="dgen.cfg" to="/home/pi/RetroPie/configs/dgen/dgenrc" />
<changeConfigPath from="gngeo.rc" to="/homepi/.gngeo/gngeorc" />

if both are changed you can fill in the Gngeo configuration
it overrides the file located in /home/pi/.gngeo

Be carefull above configuration overrides the whole file leaving you with just the joysticksettings ;o

but the joystick settings are based on gngeo 0.7 version as the config settings joystick wise differ from the 0.85 version

[quote=5215]
No, the center Xbox light is always flashing. And I would like to be able to run them all.
[/quote]

Ok, so your pad is not connecting, you will need to fix this before anything else. What type of pad is it, official? wired or wireless?

ok i’m assuming the pad is connected directly to the pi and not through an unpowered usb hub which may cause issues. Also ensure your power supply is sufficient (a 1Amp good quality PSU)

Then start with a new RetroPie image 1.9.1

run:

sudo apt-get install xboxdrv

then you need to edit rc.local with the nano txt editor:

sudo nano /etc/rc.local

add this line just before exit 0:

xboxdrv --trigger-as-button --id 0 --led 2 --deadzone 4000 --silent & sleep 1

so it reads:

fi 
xboxdrv --trigger-as-button --id 0 --led 2 --deadzone 4000 --silent & sleep 1 
exit 0

(make sure you save it, ctrl-x and press y)

then run:

cd .emulationstation 
sudo rm es_input.cfg

then reboot and follow the on screen prompts.

If you follow those instructions exactly your pad should connect on reboot and the top left led should light up instead of flashing constantly. Once you have done this we can move on to the next part.

Ok, are you able to navigate Emulation Station with your pad now?

The next step is to set your controls up. *Most* of the emulators are configured with retroarch.cfg which is a config file located in /home/pi/RetroPie/configs/all/

I have attached my retroarch.cfg which is setup with my Xbox 360 pad so should work with yours. You need to unzip the file & place it in /home/pi/RetroPie/configs/all/

You should now be able to use your pad with most of the emulators including SNES, NES, Megadrive & Playstation. If you want to swap some of the buttons around you can just edit the retroarch.cfg with:

nano /home/pi/RetroPie/configs/all/retroarch.cfg

Also you may want to set up different configs for specific emulators, you just need to copy the retroarch.cfg and place it in the relevant folder, e.g. for Megadrive put it in /home/pi/RetroPie/configs/megadrive

This will override the default retroarch.cfg in /home/pi/RetroPie/configs/all/

I have set the ‘hotkey’ button to the ‘back’ button on the pad. This means that if you press the back button and specific buttons you can access different options:

back & start = emulator exit
back & home button = Retroarch GUI (useful for setting frameskip)
back & left shoulder button = load save file
back & right shoulder button = save file
back & left trigger = select save state decrease
back & right trigger = select save state increase

There are other options you can configure with retroarch.cfg:
https://github.com/libretro/RetroArch/blob/master/retroarch.cfg

Also you may want to look at overclocking your Pi (needed for Playstation emulation and even then the Pi will struggle)

Whats your OverClock settings? :)

There are a few emulators that aren’t configured through Retroarch, hopefully you can play the ones you want now.

[quote=5243]I configured the RetroArch controls through the Emulation Station and have been able to play Master System, Game Gear, SNES, NES, and Atari games without an issue. Should I still try to do it using the method above? Are there any downsides to setting up the controls through the Emulation Station interface? Everything seems to be working, oddly enough even non-RetroArch emulators (Master System, Game Gear)[/quote]

The Emulation Station joypad config only maps the basic buttons, the retroarch.cfg I posted has a lot more buttons configured for the Xbox pad like the hotkeys etc as I mentioned. You can backup your retroarch.cfg by renaming it retroarch2.cfg or something and copy mine over.

You just insert the keymaps you want to use, you don’t need to delete any unless you’ve got conflicting keymaps. Have a look at mine for guidance. Use jtest to determine which buttons are which:

sudo apt-get install joystick

then run:

jstest /dev/input/js0

As I mentioned in the post above there are a lot more options you can configure with retroarch.cfg (anything with a # is commented out):

https://github.com/libretro/RetroArch/blob/master/retroarch.cfg

Yes it is possible to use a PS3 pad and an Xbox pad at the same time. Info here of setting up a PS3 pad:
https://github.com/retropie/RetroPie-Setup/wiki/Setting-up-a-PS3-controller
I think if you plug your bluetooth module in the second (lower) usb port it will be assigned /dev/input/js1 instead of js0

So in your retroarch.cfg you would configure player 2 controls like this:

input_player2_joypad_index = “1″
input_player2_a_btn = “13″
input_player2_b_btn = “14″

etc

Here is the list of known working bluetooth adapters: http://elinux.org/RPi_USB_Bluetooth_adapters#Working_Bluetooth_adapters

I don’t think you will be able to hot swap the bluetooth/Xbox pad, either leave both plugged in or swap and reboot.

I am having the exact same issues. I have followed all the above instructions but I cannot get my 360 controller to run in any emulations (works fine from menu). I am new to RetroPie and would love to get this working, can anyone can help?
Thanks.

Tried that, but still no joy. Thanks for the suggestion. I have also tried the setup and selected “Register controller for RetroArch emulator”. No joy again, even though it is clearly getting inputs from the controller. I am totally puzzled by this.

I’m not sure what you mean by this command, it does not appear top be a valid command. Thanks.

I noticed that from your previous post, but it simply says joystick is already the newest version and jstest is not a command that I can find

mmmm, command still not found :S